IdeaTek
currently offers support for two styles of remote. Please select the color of
the power button on your remote from the choices below:
RED
BLACK/WHITE
Programming the
Potenza Remote
Program the Remote to Control the TV
Every brand
of TV has a different TV code, and most brands have several codes. To find the
code to your TV follow the below instructions by using the search method or the
direct code entry method. It is recommended
that you put fresh batteries in the remote. When batteries begin to get low, TV
control is the first function to stop working.
Search
Method
- Turn on the
TV
- Aim the remote
at the television.
- Press the TV
button on the remote.
- While
watching the TV, press and hold the RCU SETUP button until the television blinks
twice.
- Enter the
code 991. The TV button should blink twice. If the TV button does not blink
twice, repeat the previous steps.
- Press the
POWER button. (Nothing will happen).
- Press the CH+
button repetitively until the television turns off.
- Press the
POWER button and the television should turn on.
- Press the RCU
SETUP button to save the code, and the TV button will blink twice to signal the
code was saved.
- Use the
VOLUME, MUTE, and POWER buttons to verify that the remote is now programmed to
the television. If these commands do not control the TV repeat the previous
steps to find the correct code.
Direct
Code Entry Method
- Locate the
appropriate TV code(s) for your television in the Potenza User Manual located at the bottom of this webpage.
- Turn on the
TV.
- Aim the
remote at the television.
- While
watching the TV button, press and hold the RCU SETUP button until the TV button
blinks twice.
- Use the
number keys to enter the four digit code listed for your television. If the code is accepted the TV button will blink twice.
- If the TV button does not blink or emits
a long blink, the entry was invalid. For invalid entries repeat the previous
steps and try the next code.
- Use the
VOLUME, MUTE, and POWER buttons to verify that the remote is now programmed to
the television.
- If these commands do not control the TV repeat the previous
steps and try the next code.
Program the Master Power Key
Programming
the Master Power Key allows the user to turn on/off both the TV and the STB or
DVR with one press of the power button. To program the Master Power Key follow
the directions below.
- Press and
release the STB button.
- While
watching the STB button, press and hold the SETUP button until the STB button
blinks twice.
- Use the
number keys to enter 995. The STB button will blink twice to verify the code
has been accepted.
- Press and
release the POWER button.
- Press and
release the TV button.
- While
watching the TV button, press and hold the SETUP button until the TV button
blinks twice.
- Press the STB
button.
Use the POWER
button to verify the remote is now set to control the TV and STB or DVR with
one touch. Both the TV and the STB or DVR should power on/off with a single
press of the POWER button. If the programming did not work, please repeat the
previous steps.
If you cannot find a solution to the problem you are trying to resolve please browse other common solutions at the bottom of the page.
Programming the URC2025 Remote
Program the Remote to Control the TV
Every brand of TV has a different TV code, and most brands have several
codes. To find the code to your TV follow the below instructions by using the
search method or the direct code entry method. It is recommended that you put fresh batteries in the
remote. When batteries begin to get low, TV control is the first function to
stop working.
Search Method
- Turn on the
TV
- Press and hold
SETUP until the LED light blinks twice
- Press the TV
button.
- Press and
hold the OK button until the television turns off.
- Use the
VOLUME, MUTE, and POWER buttons to verify that the remote is now programmed to
the television. If these commands do not control the TV repeat the previous
steps to find the correct code.
Direct Code
Entry Method
- Locate the
appropriate TV code(s) for your television in the URC2025 User Manual located at the bottom of this webpage.
- Turn on the
TV.
- Press the TV
button on the remote.
- While
watching the TV button, press and hold the SET UP button until the TV button
blinks twice.
- Use the
number keys to enter the four digit code listed for your television.
- If the code
is accepted the TV button will blink twice. If the TV button does not blink or emits
a long blink, the entry was invalid. For invalid entries repeat the previous
steps and try the next code.
- Use the
VOLUME, MUTE, and POWER buttons to verify that the remote is now programmed to
the television. If these commands do not control the TV repeat the previous
steps to find the correct code.
- If the remote
is not controlling the television functions repeat the previous steps until you
find the right code.
Program the Master Power Key
Programming the Master Power Key allows the user to turn on/off both the TV and the STB or DVR with one press of the power button. To program the Master Power Key follow the directions below.
- Press and release the STB button.
- While watching the STB button, press and hold the SETUP button until the STB button blinks twice.
- Use the number keys to enter 995. The STB button will blink twice to verify the code has been accepted.
- Press and release the POWER button.
- Press and release the TV button.
- While watching the TV button, press and hold the SETUP button until the TV button blinks twice.
- Press the STB button.
Use the POWER button to verify the remote is now set to control the TV and STB or DVR with one touch. Both the TV and the STB or DVR should power on/off with a single press of the POWER button. If the programming did not work, please repeat the previous steps.
If you cannot find a solution to the problem you are trying to resolve please browse other common solutions below.
Common Solutions